彩繪膜系列
LED彩光系列
透光膜系列
3D造型系列最新公告：
服務導航
Product categories
您當前位置：首頁>工程動態工程動態
裝修不用愁 軟膜天花安裝方法
發表時間：2017-02-20 14:48:50 發表作者：phpcms 瀏覽次數：141
軟膜天花是一種從國外引進，近年來被廣泛使用的室內裝飾材料，可配合各種燈光系統來營造夢幻般、無影的室內燈光效果，一般用在大型場合比較多，但也有人喜歡運用在家居餐廳、臥室等地方，下面隨小編看看軟膜天花安裝方法及注意事項。
Soft film smallpox is a kind of interior decoration materials imported from abroad, has been widely used in recent years, with various lighting systems to create a dreamy and shadowless indoor lighting effects, more commonly used in large occasions, but there are also people who love in Home Furnishing restaurant, bedroom place, following small series with soft look ceiling installation method and matters needing attention.
軟膜天花安裝方法
Soft film ceiling installation method
第一步：軟膜天花龍骨安裝
The first step: piamater ceiling keel installation
1.根據圖紙設計要求，在需要安裝軟膜天花的水平高度位置四周圍固定一圈4X4Cm支撐龍骨(有些地方面積比較大時要求分塊安裝,以達到良好效果.這樣就需要中間位置加一根木方條子)。
1 according to the requirements of design drawings, the position of the height level around the need to install piamater ceiling around a ring of 4X4Cm fixed support keel (some local area is large block installation requirements, in order to achieve good results. This requires the middle position plus a wooden note).
2. 當所有需要木方條子固定好之后，然后在支撐龍骨的底面固定安裝軟膜天花的鋁合金龍骨。
2 when all need wood slivers fixed, and then in the Aluminum Alloy keel support keel bottom fixed installation soft film ceiling.
第二步軟膜天花安裝：
The second step installation of soft film smallpox:
1、當所有的安裝軟膜天花的鋁合金龍骨固定好以后，再安裝軟膜。先把軟膜打開用專用的加熱風炮充分加熱均勻，然后用專用的插刀把軟膜張緊插到鋁合金龍骨上，最后把四周多出的軟膜修剪完整即可。
Aluminum Alloy keel 1, when all the installation of soft film smallpox is fixed, and then install the piamater. The film opened with a special heating air full uniform heating, and then use a dedicated knife inserted film tensioning is inserted into the Aluminum Alloy keel, the film can be more around the complete pruning.
2、安裝完畢后，用干凈毛巾把軟膜天花清潔干凈。
2 after installation, with a clean towel to clean soft film smallpox.
軟膜天花施工注意事項：
Matters needing attention in the construction of soft film smallpox:
1、安裝前先到工地現場檢查是否有條件安裝龍骨，現場墻身是否完成，木工部分加工是否合格，需要抹灰部分先完成，特別注意木工部分一定要按照要求來做，燈、風口等開孔尺寸要提前加工好。
1, before installation to the site to check whether the conditions of the keel wall, the scene is completed, woodworking processing part is qualified, need to pay special attention to the first part of plastering, carpentry part must be in accordance with the requirements to do, to advance the processing hole size, light air etc..
2、現場條件許可方進場施工，首先要按圖紙設計要求的木工做好部分進行固定鋁合金龍骨龍骨，注意角位一定要直角平整光滑，駁接要平、密。
2, the site conditions permit approach construction, first of all, according to the design requirements of the carpenter to do a good part of the fixed aluminum alloy keel, pay attention to the corner must be smooth and smooth, and then to be flat.
3、注意燈架、風口、光管盤要與周邊的龍骨水平，并且要求牢固平穩不能搖擺方可。
3, pay attention to the lamp holder, tuyere, light tube plate and the keel of the surrounding level, and the requirements of a firm and stable can not swing.
4、煙感、吸頂燈，先定位再做一個木底架，木底架底面要打磨光滑，并注意水平高度，太低就容易凸現底架的痕跡。
4, smoke, ceiling lamps, the first position to make a wooden frame wooden chassis underside to polish, and pay attention to the level of height is too low, it is easy to show a trace.
5、安裝天花之前，認真檢查龍骨接頭是否牢固和光滑，噴淋頭要粘上白膠帶，風口要處理好。
5, before the installation of smallpox, carefully check whether the keel joint is firm and smooth, spray head to stick on white tape, tuyere to handle.
6、安裝天花時要先從中間往兩邊固定，同時注意兩邊尺寸，注意焊接縫要直最后做角位,注意要平整光滑。四周做好后把多出的天花修剪去除。達到完美的收邊效果。
6, the installation of smallpox from the middle to both sides of the first fixed, while the attention of both sides of the size, pay attention to the last straight seam welding angle, pay attention to smooth. After more than four months to do more than the removal of smallpox pruning. To achieve the perfect edge effect.
7、開燈孔要在燈孔的位置上做好記號，把PVC燈圈小心準確地粘在軟膜的底面，待牢固后把多出的天花去除即可。
7, turn on the lights to make a mark in the lamp hole hole position, the PVC lamp ring carefully glued to the bottom surface of piamater accurately, to be strong after the removal of smallpox can be.
8、開風口、光管盤口處理就是找到風口光管盤口的位置，跟做四周一樣，把軟膜安裝到鋁合金龍骨上，注意角位要平整。做好后把多出的天花切除即可。
8, open the outlet, is to find the location of the light pipe outlet handicap handicap light tube, like around the soft film mounted to Aluminum Alloy keel, note the angle should be smooth. After the completion of the smallpox can be removed.
9、最后用干凈毛巾清潔軟膜天花表面。
At the end of 9, with a clean towel to clean the surface of soft film smallpox.
軟膜天花具有具有防火、防菌、防水、節能、環保、抗老化、安裝方便等多種優點，所以越來越成為室內吊頂材料的首選，喜歡這種新型獨特的吊頂天花的不妨多了解下。
With a soft film smallpox with fire prevention, waterproof, anti bacteria, anti ageing, environmental protection, energy saving, convenient installation and many other advantages, so more and more become the preferred indoor ceiling materials, this unique new love may wish to know more about the suspended ceiling.
編輯總結：關于軟膜天花安裝方法的相關信息就為大家介紹到這里了，希望這篇文章對大家有所幫助。如果大家還有什么不明白的地方可以在下方給小編留言哦，我們會盡快為您解答。
Edit summary: information about soft film smallpox installation method to introduce here, this article hopes to help you. If you do not understand what can be left to the bottom of the small message Oh, we will answer for you as soon as possible.
Soft film smallpox is a kind of interior decoration materials imported from abroad, has been widely used in recent years, with various lighting systems to create a dreamy and shadowless indoor lighting effects, more commonly used in large occasions, but there are also people who love in Home Furnishing restaurant, bedroom place, following small series with soft look ceiling installation method and matters needing attention.
軟膜天花安裝方法
Soft film ceiling installation method
第一步：軟膜天花龍骨安裝
The first step: piamater ceiling keel installation
1.根據圖紙設計要求，在需要安裝軟膜天花的水平高度位置四周圍固定一圈4X4Cm支撐龍骨(有些地方面積比較大時要求分塊安裝,以達到良好效果.這樣就需要中間位置加一根木方條子)。
1 according to the requirements of design drawings, the position of the height level around the need to install piamater ceiling around a ring of 4X4Cm fixed support keel (some local area is large block installation requirements, in order to achieve good results. This requires the middle position plus a wooden note).
2. 當所有需要木方條子固定好之后，然后在支撐龍骨的底面固定安裝軟膜天花的鋁合金龍骨。
2 when all need wood slivers fixed, and then in the Aluminum Alloy keel support keel bottom fixed installation soft film ceiling.
第二步軟膜天花安裝：
The second step installation of soft film smallpox:
1、當所有的安裝軟膜天花的鋁合金龍骨固定好以后，再安裝軟膜。先把軟膜打開用專用的加熱風炮充分加熱均勻，然后用專用的插刀把軟膜張緊插到鋁合金龍骨上，最后把四周多出的軟膜修剪完整即可。
Aluminum Alloy keel 1, when all the installation of soft film smallpox is fixed, and then install the piamater. The film opened with a special heating air full uniform heating, and then use a dedicated knife inserted film tensioning is inserted into the Aluminum Alloy keel, the film can be more around the complete pruning.
2、安裝完畢后，用干凈毛巾把軟膜天花清潔干凈。
2 after installation, with a clean towel to clean soft film smallpox.
軟膜天花施工注意事項：
Matters needing attention in the construction of soft film smallpox:
1、安裝前先到工地現場檢查是否有條件安裝龍骨，現場墻身是否完成，木工部分加工是否合格，需要抹灰部分先完成，特別注意木工部分一定要按照要求來做，燈、風口等開孔尺寸要提前加工好。
1, before installation to the site to check whether the conditions of the keel wall, the scene is completed, woodworking processing part is qualified, need to pay special attention to the first part of plastering, carpentry part must be in accordance with the requirements to do, to advance the processing hole size, light air etc..
2、現場條件許可方進場施工，首先要按圖紙設計要求的木工做好部分進行固定鋁合金龍骨龍骨，注意角位一定要直角平整光滑，駁接要平、密。
2, the site conditions permit approach construction, first of all, according to the design requirements of the carpenter to do a good part of the fixed aluminum alloy keel, pay attention to the corner must be smooth and smooth, and then to be flat.
3、注意燈架、風口、光管盤要與周邊的龍骨水平，并且要求牢固平穩不能搖擺方可。
3, pay attention to the lamp holder, tuyere, light tube plate and the keel of the surrounding level, and the requirements of a firm and stable can not swing.
4、煙感、吸頂燈，先定位再做一個木底架，木底架底面要打磨光滑，并注意水平高度，太低就容易凸現底架的痕跡。
4, smoke, ceiling lamps, the first position to make a wooden frame wooden chassis underside to polish, and pay attention to the level of height is too low, it is easy to show a trace.
5、安裝天花之前，認真檢查龍骨接頭是否牢固和光滑，噴淋頭要粘上白膠帶，風口要處理好。
5, before the installation of smallpox, carefully check whether the keel joint is firm and smooth, spray head to stick on white tape, tuyere to handle.
6、安裝天花時要先從中間往兩邊固定，同時注意兩邊尺寸，注意焊接縫要直最后做角位,注意要平整光滑。四周做好后把多出的天花修剪去除。達到完美的收邊效果。
6, the installation of smallpox from the middle to both sides of the first fixed, while the attention of both sides of the size, pay attention to the last straight seam welding angle, pay attention to smooth. After more than four months to do more than the removal of smallpox pruning. To achieve the perfect edge effect.
7、開燈孔要在燈孔的位置上做好記號，把PVC燈圈小心準確地粘在軟膜的底面，待牢固后把多出的天花去除即可。
7, turn on the lights to make a mark in the lamp hole hole position, the PVC lamp ring carefully glued to the bottom surface of piamater accurately, to be strong after the removal of smallpox can be.
8、開風口、光管盤口處理就是找到風口光管盤口的位置，跟做四周一樣，把軟膜安裝到鋁合金龍骨上，注意角位要平整。做好后把多出的天花切除即可。
8, open the outlet, is to find the location of the light pipe outlet handicap handicap light tube, like around the soft film mounted to Aluminum Alloy keel, note the angle should be smooth. After the completion of the smallpox can be removed.
9、最后用干凈毛巾清潔軟膜天花表面。
At the end of 9, with a clean towel to clean the surface of soft film smallpox.
軟膜天花具有具有防火、防菌、防水、節能、環保、抗老化、安裝方便等多種優點，所以越來越成為室內吊頂材料的首選，喜歡這種新型獨特的吊頂天花的不妨多了解下。
With a soft film smallpox with fire prevention, waterproof, anti bacteria, anti ageing, environmental protection, energy saving, convenient installation and many other advantages, so more and more become the preferred indoor ceiling materials, this unique new love may wish to know more about the suspended ceiling.
編輯總結：關于軟膜天花安裝方法的相關信息就為大家介紹到這里了，希望這篇文章對大家有所幫助。如果大家還有什么不明白的地方可以在下方給小編留言哦，我們會盡快為您解答。
Edit summary: information about soft film smallpox installation method to introduce here, this article hopes to help you. If you do not understand what can be left to the bottom of the small message Oh, we will answer for you as soon as possible.